Sensors & Modules

This is a DC Automatic On/Off Photocell Street Lamp Light AS-10-220 Photo Switch Controller. AC 220V 50-60Hz 10A Photo Control Photoswitch Sensor to turn on or off the light day and night without manual operation. AS-10-220 Photo Switch also can fit into solar lamps and lanterns, or cars, motorcycles, electric cars, and other power supply voltage 12V lamps and lanterns or equipment.

It is 3 axis accelerometer with on board voltage regulator IC and signal conditioned Analog voltage output.  The module is made us of ADXL335 from Analog Devices. The product measures acceleration with a minimum full-scale range of ±3 g. It can measure the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion, shock, or vibration. The user selects the bandwidth of the accelerometer using the CX, CY, and CZ capacitors at the XOUT, YOUT, and ZOUT pins. Bandwidths can be selected to suit the application, with a range of 0.5 Hz to 1600 Hz for the X and Y axes, and a range of 0.5 Hz to 550 Hz for the Z axis.This is the latest in a long, proven line of analog sensors – the holy grail of accelerometers. The ADXL335 is a triple axis accelerometer with extremely low noise and power consumption – only 320uA! The sensor has a full sensing range of +/-3g. There is an on-board voltage regulation, which enable you to power the board with 3V to 6V DC. Board comes fully assembled and tested with external components installed. The included 0.1uF capacitors set the bandwidth of each axis to 50Hz.

350.00 Price Excluding GST of 18%

This ADXL345 Triple axis accelerometer module is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16g. Digital output data is format as 16-bit twos complement and is accessible through either an SPI (3- or 4-wire) or I2C digital interface.
The ADXL345 Triple axis accelerometer module is well suited for mobile device applications. It measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Its high resolution (4mg /LSB) enables resolution of inclination changes of as little as 0.25°.

110.00 Price Excluding GST of 18%

HX710B Atmospheric Pressure Sensor Module. This barometric pressure sensor is optimized for altimeters and variometers with an altitude resolution of 10 cm. The sensor module includes a high linearity pressure sensor and an ultra-low power; 24 bit  ADC with internal factory calibrated coefficients. It provides a precise digital 24 Bit pressure and temperature value and different operation modes that allow the user to optimize for conversion speed and current consumption. This HX710B air pressure sensor module uses a high-precision AD sampling chip, adopts a 0-40KPa air pressure sensor, can connect a 2.5mm hose, can detect water level, and other air pressure

120.00 Price Excluding GST of 18%

85.00 Price Excluding GST of 18%

BME280 sensor, an environmental sensor with temperature, barometric pressure and humidity! This sensor is great for all sorts of weather/environmental/MICROWAVE sensing and can even be used in I2C. This precision sensor from Bosch is the best low-cost sensing solution for measuring humidity with ±3% accuracy, barometric pressure with ±1 hPa absolute accuraccy, and temperature with ±1.0°C accuracy. Because pressure changes with altitude, and the pressure measurements are so good, you can also use it as an altimeter with  ±1 meter or better accuracy! The BME280 is the next-generation of sensors from Bosch, and is the upgrade to the BMP085/BMP180/BMP183 – with a low altitude noise of 0.25m and the same fast conversion time. For simple easy wiring, go with I2C.

270.00 Price Excluding GST of 18%

The BME680 is a low-power sensor that detects with high linearity and accuracy temperature, humidity, barometric pressure, and VOC gas. It includes both SPI and I2C interfaces for reading the measured values using our preferred microcontrollers (e.g., compatible with Arduino, ESP8266) and single-board computers (e.g., Raspberry Pi). This high-precision sensor can measure humidity with ±3% accuracy, barometric pressure with ±1 hPa absolute accuracy, and temperature with ±1.0°C accuracy. Because of the accuracy in pressure, the sensor can be used to estimate altitude within ±1 meters! The gas sensor works by changes in its internal resistance, which is designed to be sensitive to changes in the concentration of Volatile Organic Compound (VOC) gases. Although the sensor works great, it should not be used for any safety, medical, or finished product usage. All gas sensors require calibration for precision output.

720.00 Price Excluding GST of 18%

BMP180 Digital Barometric Sensor Module compatible with Arduino will Measure the absolute pressure of the environment using a digital barometer such as this has some interesting applications. By converting the pressure measured into altitude, you have a reliable sensor for determining the height of your robot, plane or projectile! Using a sensor as capable as the BMP180 you can achieve an accuracy of 1m, with the noise of only 17cm in ultra-high resolution noise.

32.00 Price Excluding GST of 18%

BMP280 Barometric Pressure and Altitude Sensor I2C/SPI Module is a cheapest and tiny Atmospheric Sensor Breakout to measure barometric pressure, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BMP280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.

32.00 Price Excluding GST of 18%

The TCS3200 Color Recognition Sensor Module for MCU Arduino uses a high-quality light sensor allowing you to sense any color through a combination of Red, Green, and Blue. The module provides all of the pins of the TCS3200 on convenient 0.1″ headers – ideal for use with PCBs, breadboard or stripboard. Four white LEDs provide plenty of light for the color sensor and allow you to use the module in any ambient light.

350.00 Price Excluding GST of 18%

The CJMCU-34725 TCS34725 Color Sensor RGB Module lets you sense the color of objects. It lets the microcontroller read object color values for red, green, and blue (RGB). It comes with a Color-sensitive photodiode integrated and localised infrared shading filter to minimize the external light noise. Just connect it to your microcontroller, point the sensor to objects and start reading the color values! It is much more accurate than the standard color sensor. It has high sensitivity, a wide dynamic range, and IR shading filters, which make it work even in challenging light environments.

300.00 Price Excluding GST of 18%

The 20A Range Current Sensor Module ACS712 consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field in which the Hall IC converts into a proportional voltage. Sensing and controlling current flow is a fundamental requirement in a wide variety of applications including, over-current protection circuits, battery chargers, switching mode power supplies, digital watt meters, programmable current sources, etc. This ACS721 current module is based on the ACS712 sensor, which can accurately detect AC or DC current.

75.00 Price Excluding GST of 18%

The 30A range Current Sensor Module ACS712 consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field in which the Hall IC converts into a proportional voltage.

75.00 Price Excluding GST of 18%

The 5A range Current Sensor Module ACS712 consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field in which the Hall IC converts into a proportional voltage.

75.00 Price Excluding GST of 18%

The WCS1700 consists of a precise, low-temperature drift linear hall sensor IC with a temperature compensation circuit and diameter of 9.0mm through-hole. Users can use the system’s own electric wire to bypass it through this hole to measure passing current. This design allows system designers to monitor any current path without breaking or changing the original system layout at all. Any current flowing through this hole will generate a magnetic field that is sensed by the integrated Hall IC and converted into a proportional voltage.

This is SCT 013 000 100A Non-Invasive AC Current Sensor Split Core Type Clamp Meter Sensor. SCT-013-000 is a Non-Invasive AC current sensor i.e. it is a current transformer that can be used to measure AC current up to 100 amperes. Current transformers (CTs) are sensors are for measuring alternating current. They are particularly useful for measuring whole building electricity consumption (or generation for that matter). The split-core type such as the SCT-013-000 CT in the picture is particularly suitable for DIY use. Clip this SCT 013 000 straight onto either the live or neutral wire coming into the building without having to do any high voltage electrical work.

340.00 Price Excluding GST of 18%

This is SCT-013-030 Non-invasive AC Current Sensor Clamp Sensor 30A. SCT-013-000 is a Non-Invasive AC current sensor i.e. it is a current transformer that can be used to measure AC current up to 100 amperes. This Non-invasive AC Current Sensor clamped around the supply line can measure a load up to 30 Amps, and allow you to calculate how much current pass through it. It can be useful for building your own energy monitor or for building an over-current protection device for an AC load. This current clamp can be used to detect a current of up to 30A. Simply clip it around the current source that you wish to measure and it will produce a (very) small AC voltage proportional to the current. The cable is terminated on one end with a standard 3.5mm jack

340.00 Price Excluding GST of 18%

The DHT11 Humidity & Temperature Sensor Module is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and outputs a digital signal on the data pin (no analog input pins needed). Its very simple to use, and libraries and sample codes are available for Arduino and Raspberry Pi.  

60.00 Price Excluding GST of 18%

The DHT22 Digital Temperature and Humidity Sensor Module AM2302 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and spits out a digital signal on the data pin (no analog input pins needed).

125.00 Price Excluding GST of 18%

The Waterproof DS18B20 Digital Temperature Sensor Probe is a temperature probe designed for reliable performance in a variety of environments, including wet or damp conditions. This sensor operates in a temperature range of -55°C to +125°C (-67°F to +257°F) with an accuracy of ±0.5°C in the typical range of -10°C to +85°C, making it ideal for applications such as weather stations, HVAC systems, and liquid temperature monitoring. The DS18B20 sensor features a digital output via a 1-Wire interface, allowing multiple sensors to share a single data line. It offers a configurable resolution of 9 to 12 bits, providing precise temperature readings. The sensor is enclosed in a stainless steel probe, ensuring durability and complete waterproofing, which makes it suitable for direct immersion in water or other liquids. It is powered by a voltage range of 3.0V to 5.5V, making it compatible with most microcontrollers and development boards. The probe comes with a 1m, 3m and 5m cable, offering flexibility for installation as pre requirement..

62.00 Price Excluding GST of 18%

This PM2.5 GP2Y1010AU0F Dust Smoke Particle Sensor is an infrared emitting diode (IRED) and a phototransistor are diagonally arranged into this device. It detects the reflected light of dust in the air. Especially, it is effective to detect very fine particle like the cigarette smoke. In addition, it can distinguish smoke from house dust by the pulse pattern of the output voltage.

325.00 Price Excluding GST of 18%

The E18-D80NK Adjustable Infrared Sensor Switch 3-80cm is a set of transmitter and receiver in one of the photoelectric switch sensor. The detection distance can be adjusted according to the demand. The sensor has a detection range of 3-80cm.

145.00 Price Excluding GST of 18%

The Heart Rate Monitor Kit with AD8232 ECG sensor module Kit For Arduino is a cost-effective board use to measure the electrical activity of the heart. This electrical activity can be chart as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily. The ECG module AD8232 heart ECG monitoring sensor module is an integrated signal conditioning block for ECG and other bio-potential measurement applications. The ECG Module AD8232 Heart ECG Monitoring Sensor Module Kit for Arduino is designed to extract, amplify, and filter small bio-potential signals in the presence of noisy conditions; such as those created by motion or remote electrode placement.

395.00 Price Excluding GST of 18%

EMG Muscle Sensor V3.0 With Cable And Electrodes will measure the filtered and rectified electrical activity of a muscle; outputting 0-Vs Volts depending the amount of activity in the selected muscle, where Vs signifies the voltage of the power source. Power supply voltage: min. +-3.5V. EMG Muscle Sensor v3 measures, filters, rectifies, and amplifies the electrical activity of a muscle and produces an analogue output signal that can easily be read by a microcontroller, enabling novel, muscle-controlled interfaces for your projects.

1,357.00 Price Excluding GST of 18%

The eye–blink sensor works by illuminating the eye and eyelid area with infrared light, then monitoring the changes in the reflected light using a photo-transistor and differentiator circuit. The exact functionality depends greatly on the positioning and aiming of the emitter and detector with respect to the eye.

125.00 Price Excluding GST of 18%

This is the R307S Optical Fingerprint Reader Sensor Module. R307S fingerprint module is a fingerprint sensor with a TTL UART interface for direct connections to microcontroller UART or to PC through MAX232 / USB-Serial adapter. The user can store the fingerprint data in the module and can configure it in 1:1 or 1: N mode for identifying the person. The FP module can directly interface with a 3.3 or 5v Microcontroller. A level converter (like MAX232) is required for interfacing with PC serial port. Integrated image collecting and algorithm chip together, ALL-in-One Fingerprint reader can conduct secondary development, can be embedded into a variety of end products. Users can conduct secondary development, can be embedded into a variety of end products, such as access control, attendance, safety deposit box, car door locks.

790.00 Price Excluding GST of 18%

This sensor module is primarily used to detect an open flame.  It does this by detecting light that is in the IR (infrared) spectrum which is emitted by a flame.  That spectrum is typically in the range of 700-1100nm. This module is similar to a regular IR detector, but with a broader detection range.  It can be used as a general IR detector for other applications where a broad detection range is desired

28.00 Price Excluding GST of 18%

A simple Flex Sensor 2.2″ – Bend Sensor with a length of 2.2″ which bends and flexes with a physical device. As the sensor is flex, the resistance across the sensor increases. A connector is 0.1″ spaced and breadboard friendly. Applications in – Robotics, Gaming (Virtual Motion), Medical Devices, Computer Peripherals, Musical Instruments, Physical Therapy.
The flex sensor is a bend detecting sensor that has got numerous applications in robotics, medical and haptic technology. The resistance of these sensors changes in accordance with the bend, which can be measured using any microcontroller.

220.00 Price Excluding GST of 18%

Sharp GP2Y0A21 sensor can be used to detect objects within the range of 10cm to 80cm. The sensor senses objects ahead of it and output an analog voltage corresponding to the distance between the sensor and the object. You can easily read this signal from the ADC for an Arduino/Raspberry Pi or a Microcontroller and get the distance of the object. This sharp sensor is great to add obstacle avoidance or motion sensing to your robot or any other project. The sensor comes with a compatible 3 pin JST 3-pin connector with crimped wires.

375.00 Price Excluding GST of 18%

The Linear Magnetic Hall Sensor, also known as the ky 024 hall sensor, is an advanced module designed for detecting magnetic fields through digital and analog interfaces. This hall effect sensor is tailored for use in systems needing precise magnetic sensing capabilities. Powered by an operating voltage of 3.3V to 5V, this sensor includes a comparator LM393 for a broad range of voltage operations. The hall effect pickup feature is adjustable, and there’s a signal output indicator for easy installation. When a magnetic field is sensed, the hall effect detector will emit a low-level digital signal, activating an LED indicator. This functionality is ideal for numerous applications, including motor speed measurement and object position detection. The hall ic sensor operates using semiconductor technology, ensuring precise and reliable magnetic field detection, with outputs available in both digital and analog forms. It converts magnetic information into a proportional electrical signal, facilitating accurate magnetic field measurement crucial for hall effect and sensors applications.

33.00 Price Excluding GST of 18%

The Linear Magnetic Hall Sensor, also known as the ky 024 hall sensor, is an advanced module designed for detecting magnetic fields through digital and analog interfaces. This hall effect sensor is tailored for use in systems needing precise magnetic sensing capabilities. Powered by an operating voltage of 3.3V to 5V, this sensor includes a comparator LM393 for a broad range of voltage operations. The hall effect pickup feature is adjustable, and there’s a signal output indicator for easy installation. When a magnetic field is sensed, the hall effect detector will emit a low-level digital signal, activating an LED indicator. This functionality is ideal for numerous applications, including motor speed measurement and object position detection. The hall ic sensor operates using semiconductor technology, ensuring precise and reliable magnetic field detection, with outputs available in both digital and analog forms. It converts magnetic information into a proportional electrical signal, facilitating accurate magnetic field measurement crucial for hall effect and sensors applications.

33.00 Price Excluding GST of 18%

HC-SR505 Mini Infrared PIR Motion Sensor Infrared Detector Module is based on infrared technology, It automatically controls the products with high sensitivity, high reliability, ultra-small size, and ultra-low-voltage operation mode.

73.00 Price Excluding GST of 18%

The 10K NTC Thermistor temperature sensor module is a low-cost, small-size module. It is very sensitive to ambient temperature. It is generally used to detect the temperature of the surrounding environment. Through potentiometer adjustment, it is possible to change the temperature detection threshold. DO output can be directly connected to the microcontroller to detect high and low, by detecting temperature changes in the environment. The temperature detection range of the module is between 20 and 80 degrees Celsius.

33.00 Price Excluding GST of 18%

The HMC5883L is a 3-axis Digital Compass IC for low-field magnetic sensing with a digital interface for applications such as low cost compassing and magnetometry. The HMC5883L includes our state-of-the art, high-resolution HMC118X series magneto-resistive sensors plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation and a 12-bit ADC that enables 1 to 2° compass heading accuracy. The I²C serial bus allows for easy interface. It utilizes Anisotropic Magnetoresistive (AMR) technology that provides advantages over other magnetic sensor technologies. These anisotropic, directional sensors feature precision in-axis sensitivity and linearity. These sensors’ solid-state construction with very low cross-axis sensitivity is designed to measure both the direction and the magnitude of Earth’s magnetic fields, from milli-gauss to 8 gauss.

129.00 Price Excluding GST of 18%

TSOP1738 IR Receiver – Infrared Receiver. The TSOP1738 IR Receiver, also known as an Infrared Receiver, is a compact sensor designed for IR remote control systems. It comprises a PIN diode and a preamplifier integrated onto the lead frame, enclosed in an epoxy package that acts as an IR filter. Part of the TSOP series, this sensor is widely compatible with various controllers and processors, enabling direct decoding of the demodulated output.

68.00 Price Excluding GST of 18%

The IR Proximity Sensor has a distance range of 2cm to 30cm and it is ideal for obstacle detection, line tracking, and more. The detection range of the infrared proximity sensor can be adjusted by the potentiometer.

22.00 Price Excluding GST of 18%

Introducing the 4 IR Sensor Array Module, a versatile and reliable sensor system designed for precise detection in various applications. This module features four IR sensor arrays, each equipped with an IR transmitter and an IR receiver. With an adjustable detection range from 1mm to 20cm, this sensor module offers flexibility to meet diverse proximity requirements. It performs optimally when the distance is closer, ensuring stable operation. Notably, white objects reflect infrared light the farthest, enhancing detection accuracy.

120.00 Price Excluding GST of 18%

This IR sensor module contains 8 IR LED/phototransistor pairs. Each sensor has a separate digital I/O measurable output. This reflection sensor array is designed to be used as a line sensor, but it may also be used as a proximity or reflection sensor. The module serves as a carrier for eight IR emitter and receiver (photo-transistor) pairs that are uniformly placed at 0.35″ inch intervals.

200.00 Price Excluding GST of 18%

This KY-008 Laser Module 650nm 5V is very easy to use, you can use Arduino control, do controllable laser pointer, theft detection, etc. interesting application devices. The laser head is composed of a light-emitting tube, condenser lens and adjustable copper sleeve and it is assembled when delivered, the focal length of the lens is adjusted glued by strong glue stick, which can work directly after connecting to a 5V DC power supply. The laser is not a toy, do not give children, mental insufficiency, for people who do not understand the use of the laser characteristics, in this case, can easily lead to injury. The use of lasers should wear special goggles, for the invisible laser, this point is particularly important. The laser cannot shine in vehicles, aircraft and other transport vehicles someone.

30.00 Price Excluding GST of 18%

Ambient light sensing is a significant part of many applications like automatic street lights, solar panels charging controller, automatic irrigations systems where humidity and ambient light determine if the plant needs to be irrigated or not. We usually use a simple Light Dependent Resistor (LDR) as it changes its resistance with the amount of light falling over it, which gives us an idea about the light intensity in the surrounding. But in some cases, we want to know if the light is beyond certain threshold to trigger certain processes in which case this Photosensitive Light Detection sensor module which gives digital output and whose sensitivity can be adjusted with the onboard potentiometer is a great module to use. It has onboard LM393 comparator IC to convert analog signals coming from lDR to the Digital Signals that can be used to connect with the microcontroller or development board you are using.

24.00 Price Excluding GST of 18%

TFmini-S is a single-point ranging LiDAR based on the TFmini upgrade. The blind zone is shortened from 30cm to 10cm, the outdoor performance and accuracy of different reflectivity are improved. The distance range is not disturbed by ambient light, which can be consistent with the indoor range and the accuracy is further optimized. The error performance at 10% reflectivity approaches the background of 90% reflectivity, and the interface supports UART and I2C switching at any time. It can achieve stable, accurate, sensitive, and high-frequency range detection.

Li-Fi stands for Light Fidelity .Li-Fi technology provides transmission of data through illumination by sending  data  through  LED  that  varies  in  intensity  faster  than  the  human  eye  can  follow.This  product  focus  on developing  a  Li-Fi  based  system  and  analyze  its  performance  with  respect  to  existing  technology. The  heart  of this technology is a new generation  of high brightness  LEDs. The  product consisting of  a  transmitter  which  includes  a  light  source  and  the  receiver  circuit  which  receives  the  data  transmitted  via light waves. The same system can be employed in industries making industrial automation using the existing light source a reality. A biomedical sensor is also introduced herewith which helps in diagnosis of a patient’s medical conditions and is quickly made available to all the emergency points through light.

LM35 is a low cost, linear and precise temperature measuring IC. It gives an Analog Output Voltage proportional to the temperature it measures. It also does not require any additional calibration circuit to give the output in degree Celsius. It also has less self-heating (0.1 ̊ C in still air) property than the thermistor. It is extremely popular among the hobbyists, DIY Circuit makers and Students even after 16 years of its launch. It has also been used in many low-end products where we require to measure the temperature with greater precision while keeping the cost low. You can use it in Temperature measurement of Battery Pack, Air, Boiling Water, any Electric Circuit etc. The sensor has two-part names lm35dz and lm35dt.

This load cell (sometimes called a pressure gauge) can translate up to 10kg of stress (force) into an electric signal. Each load cell can measure the electrical resistance that changes in response to, and proportionality of, the strain (e.g. pressure or force) applied to the pub. With this gauge, you will have the ability to tell just how heavy an object is if an item’s weight varies over time, or in the event that you merely must sense the presence of an object by measuring load or strain applied to a surface.

106.00 Price Excluding GST of 18%

This weighing Load Cell Sensor (sometimes called a strain gauge) can translate up to 1 kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain (e.g. pressure or force) applied to the bar.

106.00 Price Excluding GST of 18%

This Load cell can be used to measure the weight of objects between 0 and 20kg. This straight bar load cell (sometimes called a strain gauge) can translate up to 20kg of pressure (force) into an electrical signal. Each load cell can measure the electrical resistance that changes in response to, and is proportional to, the strain (e.g. pressure or force) applied to the bar. With this gauge, you will be able to tell just how heavy an object is, if an object’s weight changes over time, or if you simply need to sense the presence of an object by measuring strain or load applied to a surface.

106.00 Price Excluding GST of 18%

This Load cell can be used to measure the weight of objects between 0 and 3kg. This straight bar load cell (sometimes called a strain gauge) can translate up to 3 kg of pressure (force) into an electrical signal. Each load cell can measure the electrical resistance that changes in response to, and is proportional to, the strain (e.g. pressure or force) applied to the bar. With this gauge, you will be able to tell just how heavy an object is, if an object’s weight changes over time, or if you simply need to sense the presence of an object by measuring strain or load applied to a surface.

106.00 Price Excluding GST of 18%

This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportionality of, the strain (e.g. pressure or force) applied to the bar. With this gauge, you will be able to tell just how heavy an object is, if an object’s weight changes over time, or if you simply need to sense the presence of an object by measuring strain or load applied to a surface.

106.00 Price Excluding GST of 18%

MAX30100 an optical sensor that derives its readings from emitting two wavelengths of light from two LEDs – a red and an infrared one – then measuring the absorbance of pulsing blood through a photodetector. This particular LED color combination is optimized for reading the data through the tip of one’s finger. The signal is processed by a low-noise analog signal processing unit and communicated to the target MCU through the mikroBUS I2C interface. Developers of end-user applications should note that the readings can be negatively impacted by excess motion and changes in temperature. Also, too much pressure can constrict capillary blood flow and therefore diminish the reliability of the data. A programmable INT pin is also available. The operates at the 3.3V power supply.

100.00 Price Excluding GST of 18%

MAX30102 is an integrated pulse oximeter and heart-rate monitor sensor solution. It’s an optical sensor that derives its readings from emitting two wavelengths of light from two LEDs – a red and an infrared one – then measuring the absorbance of pulsing blood through a photodetector. This particular LED colour combination is optimized for reading the data through the tip of one’s finger. It is fully configurable through software registers and the digital output data is stored in a 16-deep FIFO within the device. It has an I2C digital interface to communicate with a host microcontroller.

110.00 Price Excluding GST of 18%

The MAX31865 is an easy-to-use thermistor to digital output converter optimized for platinum resistance temperature detectors (RTD). The external resistor sets the RTD sensitivity, and the high-precision Δ- ΣADC converts the RTD resistor and the reference resistor to digital output. The MAX31865 input has overvoltage protection of up to ± 45V, providing configurable RTD and cable open, short circuit condition detection.

You can use this LC Metal detector non-contact metal induction detection module as a metal detector. When it approaches any metal, it makes a sound. This is a module specifically designed to detect metal. The module operates by inducing currents in metal objects and responding when it occurs. A nice onboard buzzer signals when it detects something and an onboard potentiometer allows adjustment of sensitivity. The power cables of the Metal detector non-contact metal induction detection module will need soldering on for the module to function, positive to the outside of the module and negative between the potentiometer and an electrolytic capacitor.

40.00 Price Excluding GST of 18%

The RCWL-0516 Microwave Radar Sensor is a mini doppler radar sensor module equipped with supporting DC 4-28V wide voltage. It is an alternative to the PIR sensor and uses in many security alarms system. This is a mini radar motion sensor module equipped with RCWL-9196 chip based on the doppler microwave induction technology. It will automatically continuously output the high-level TTL signal when there is motion with adjustable delay time and sensitivity. It is perfect for DIY microwave motion sensor light switch, human sensor toys, smart security devices, etc. The output of the RCWL-0516 sensor is analog and can be connected to an analog input of a microcontroller and sampled by an ADC. The output voltage is roughly proportional to the distance between the sensor and the object. However, since it relies on a Doppler radar system, signal reflections from other nearby objects can interfere with the measurement, making it less reliable and accurate than other kinds of sensors. The reflections from different kinds of objects can also influence measurements, for example, metallic objects have a stronger reflection than plastic objects.

35.00 Price Excluding GST of 18%

The circuit board product voltage is USB 5V, current 300mA, power 2W, frequency 113KHz\108KHz, and special drive chip for fixed frequency atomizer. Immediately after power-on, the amount of output is large. With 8-hour timing function, an external switch can be used to control the opening and closing of the atomizer. These waves are used to create the mist that can be inhaled.

110.00 Price Excluding GST of 18%

The MLX90614 ESF is an Infra-Red thermometer for non-contact temperature measurements.  Both the IR-sensitive thermopile detector chip and the signal conditioning ASIC are integrated into the same TO-39 can. The Integrated MLX90614 GY-906 is a low noise amplifier, 17-bit ADC, and powerful DSP unit thus achieving high accuracy and resolution of the thermometer. The user can configure the digital output to be PWM. As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in the range of -20 to 120 °C, with an output resolution of 0.14 °C.

708.00 Price Excluding GST of 18%

The MOC7811 Slotted Opto Isolator Module is designed for non-contact object sensing applications. This module integrates an IR LED and a photodiode, allowing it to detect objects without direct contact. Ideal for positional sensing tasks, such as limit switches and position encoders, it fits various projects. Its compact design ensures easy integration into existing systems, making it perfect for automation and robotics applications.

22.00 Price Excluding GST of 18%

The OE-775 Hall Effect Two-Channel Magnetic Encoder is a high-precision rotary encoder designed for motion control applications. It uses a hall-effect sensor to detect magnetic field changes, ensuring accurate speed and position feedback. The encoder features two output channels (A & B) for quadrature signal detection, enabling direction sensing. With a compact circular PCB design, it is ideal for integration into motors and robotic systems. The 3-wire interface (VCC, GND, A, B) ensures easy connectivity, while the durable construction enhances reliability in industrial and automation applications.

MPR121 is a capacitive touch sensor controller driven by an I2C interface. The chip can control up to twelve individual electrodes, as well as a simulated thirteenth electrode The MPR121 also features eight LED driving… pins, when these pins are not configured as electrodes, they may be used to drive LEDs.There a four jumpers on the bottom of the board, all of which are set (closed) by default.

80.00 Price Excluding GST of 18%

The module uses MPU-6050 which is a little piece of motion processing tech! By combining a 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor capable of processing complex 9-axis MotionFusion algorithms, the MPU-6050 does away with the cross-axis alignment problems that can creep up on discrete parts.

177.00 Price Excluding GST of 18%

MPU9250 6-Axis Attitude Gyro Accelerator Sensor Module features the MPU-9250, which is a multi-chip module (MCM) consisting of two dies integrated into a single QFN package. One die houses the 3-Axis  accelerometer and gyroscope. Hence, the MPU-9250 is a 6-axis Motion Tracking device that combines a 3-axis accelerometer and gyroscope and a Digital Motion Processor (DMP). It is based on I2C Address, Address: 0x68 by default, 0x69 if AD0 is pulled high. The MPU-9250 also features an embedded temperature sensor. This module includes pull-up resistors on the SDA, SCL, and nCS lines, pull-down resistors on the FSYNC and AD0 lines, and an onboard 3.3V voltage regulator allowing you to power the module from 5V sources such as an Arduino. If you desire to power the module from 3.3V you can bridge the solder jumper next to the voltage regulator to bypass the regulator.

531.00 Price Excluding GST of 18%

The MPX10DP is a dual-port uncompensated silicon Pressure Sensor for environmental control systems and level indicators. The MPX10 series silicon piezoresistive pressure sensor provides a very accurate and linear voltage output, directly proportional to the applied pressure. This standard uncompensated sensor permits manufacturers to design and add their own external temperature compensation and signal conditioning networks. Compensation techniques are simplified because of the predictability of NXP’s single element strain gauge design.

525.00 Price Excluding GST of 18%

MQ135 gas sensor has high sensitivity to Ammonia, Sulfide and Benzene steam, also sensitive to smoke and other harmful gases.

95.00 Price Excluding GST of 18%

The MQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module is useful for gas leakage detection (home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol, Smoke, or Propane.

78.00 Price Excluding GST of 18%

MQ-3 Alcohol Detector Gas Sensor Module is simple to use. MQ-3 Alcohol Detector Module which can sense the presence of Alcohol in the air. The module uses our MQ-3 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides an interface through standard 4 x 0.1″ header pins.

105.00 Price Excluding GST of 18%

The MQ4 methane gas sensor is extremely used for detecting gas leakage at home or in industries like Methane (CH4) & CNG Gas. This gas sensor is highly responsive in very little time, so based on the sensitivity requirements; it can be adjusted through a potentiometer. This is an analog output sensor, used like a CNG (compressed natural gas) sensor within the series of MQ sensors.

85.00 Price Excluding GST of 18%

This MQ-5 Methane LPG Liquid Propane Gas Sensor Module is widely used in gas leakage detecting pieces of equipment in family and industry, are suitable for detecting LPG, natural gas, town gas, avoid the noise of alcohol and cooking fumes and cigarette smoke

85.00 Price Excluding GST of 18%

This is a simple-to-use MQ-6 Liquefied Petroleum Isobutane Propane Gas Sensor module, suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 200 to 10000ppmThe MQ-6 Liquefied Petroleum Isobutane Propane Gas Sensor module particulate sensor uses a Potentiometer to change the detection range of the sensor! 

78.00 Price Excluding GST of 18%

This coin acceptor will accept as many as six distinct coin types! The thickness, diameter, and fall time of the coins are used by the sensors in this coin acceptor to identify them, and it is entirely customizable so you are not restricted to any certain sort of currency. By analyzing the coin’s mass, size, diameter, thickness, metal composition, and/or magnetism, the coin selector determines which coin it is, and after that, sends the proper electrical signal via its output link. It also contains a coin reject button that your controller may use to instruct it to stop accepting coins. A pocket full of change, a 12 VDC supply, and a place for the change to fall once it is accepted are all you need to get the coin acceptor running. It can be easily interfaced with any sensors.

1,000.00 Price Excluding GST of 18%

NPK, Five-Pin Soil Multi-Parameter Sensor (RS485 Type) is a five-pin multi-parameter soil sensor designed for accurate and reliable measurement of soil temperature, moisture, pH, conductivity, nitrogen, phosphorus, and potassium. Engineered for durability, it features high sensitivity, fast response, and waterproof IP68 sealing, making it ideal for long-term in-situ monitoring.

3,540.00 Price Excluding GST of 18%

The TEC1-12706 40x40mm Thermoelectric Cooler 5A Peltier Module is the simple application of Peltier Thermoelectric Effect. The module features 127 semiconductor couples in the area of 40mmx40mm which very effectively cools and heats up to 80°C. Thermoelectric coolers also are known as TEC or Peltier Module create a temperature differential on each side. One side gets hot and the other side gets cool. Therefore, they can be used to either warm something up or cool something down, depending on which side you use. You can also take advantage of a temperature differential to generate electricity. This Peltier works very well as long as you remove the heat from the hot side. After turning on the device, the hot side will heat quickly, the cold side will cool quickly. If you do not remove the heat from the hot side (with a heat sink or other device), the Peltier will quickly reach stasis and do nothing. We recommend using an old computer CPU heatsink or another block of metal to pull heat from the hot side. We were able to use a computer power supply and CPU heatsink to make the cold side so uncomfortable we could not hold our finger to it. A thermoelectric cooling (TEC) module is a semiconductor-based electronic component that functions as a small heat pump. By applying the DC power source to a TEC, heat will be transferred from one side of the module to the other. It creates a cold and hot side. They are widely used in industrial areas, for example, computer CPU, CCDs, portable refrigerators, medical instruments, and so on.

525.00 Price Excluding GST of 18%

This PH Sensor Module is Compatible for Arduino. The pH stands for the power of hydrogen, which is a measurement of the hydrogen ion concentration in the body. This is used in Water quality testing and Aquaculture. The total pH scale ranges from 1 to 14, with 7 considered to be neutral. A pH less than 7 is said to be acidic and solutions with a pH greater than 7 are basic or alkaline.The PH electrode has a single cylinder that allows direct connection to the input terminal of a pH meter, controller, or any pH device which has a BNC input terminal. The pH electrode probe is accurate and reliable that can give almost instantaneous readings.

1,298.00 Price Excluding GST of 18%

The HC-SR501 PIR Motion Sensor Module used to detect the motion of a human body within the sensor’s range. It is often referred to as “PIR”, “Pyroelectric”, “Passive Infrared” and “IR Motion Sensor” sensors. The PIR Motion sensor module has an onboard pyroelectric sensor, conditioning circuitry, and a dome-shaped Fresnel lens.

59.00 Price Excluding GST of 18%

Pulse Sensor is a low-cost, very small-size plug-and-play heart rate sensor for Arduino and Arduino compatible boards. It can be used by students, artists, athletes, makers, and game & mobile developers who want to incorporate live heart-rate data into their projects easily. Pulse Sensor Amped adds amplification and noise cancellation circuitry to the hardware. This heart rate sensor is noticeably faster and easier to get reliable pulse readings. Pulse Sensor works with either a 3V or 5V Arduino.

120.00 Price Excluding GST of 18%

The Raindrops Detection sensor module is used for rain detection. This raindrop sensor is also used for measuring rainfall intensity. The rain sensor can be used for all kinds of weather monitoring and translated into output signals and AO. Raindrops Detection Sensor Module for Arduino, etc. The rain sensor can be used to monitor a variety of weather conditions and turned into several fixed output signals and Analog.

42.00 Price Excluding GST of 18%

The M274 360 Degree Rotary Encoder Brick Sensor Module is a rotary input device (as in knob) that provides an indication of how much the knob has been rotated AND what direction it is rotating in. It’s a great device for stepper and servo motor control. You could also use it to control devices like digital potentiometers.

39.00 Price Excluding GST of 18%

Start building real electronics projects from day one with this complete 37-in-1 Sensor Module Kit. Designed for Arduino and Raspberry Pi users, this all-in-one collection gives you instant access to the most essential sensors and interface modules used in robotics, automation, and IoT development. Instead of buying modules separately, this kit brings together 37 carefully selected modules covering temperature, sound, light, motion, magnetic detection, IR communication, relay control, and user input devices. Each module comes pre-mounted on a PCB with standard 3-pin headers, making wiring fast, clean, and beginner-friendly. Whether you’re a student learning embedded systems, a hobbyist experimenting with sensors, or a developer prototyping new ideas, this kit saves time, reduces confusion, and accelerates hands-on learning.

885.00 Price Excluding GST of 18%

This Capacitive Soil Moisture Sensor V1.2 measures soil moisture levels by capacitive sensing rather than resistive sensing like other sensors on the market. It is made of corrosion resistant material which gives it an excellent service life. Insert it into the soil around your plants. This module includes an onboard voltage regulator which gives it an operating voltage range of 3.3 ~ 5.5V. It is perfect for low-voltage MCUs, both 3.3V and 5V. For compatibility with a Raspberry Pi, it will need an ADC converter.

50.00 Price Excluding GST of 18%

This is a Soil Moisture Sensor or Soil Humidity Sensor. With this module, you can tell when your plants need watering by how moist the soil is in your pot, garden, or yard. Use it in a home automated watering system, hook it up to IoT, or just use it to find out when your plant needs a little care. Installing this sensor and its PCB will have you on your way to growing a green thumb! This soil moisture sensor consists of two probes which are used to measure the volumetric content of water. The two probes allow the current to pass through the soil and then it gets the resistance value to measure the moisture value.

31.00 Price Excluding GST of 18%

The sound detection sensor module for Arduino detects whether the sound has exceeded a threshold value. Sound is detected via microphone and fed into an LM393 op-amp. The sound level set point is adjusted via an onboard potentiometer. When the sound level exceeds the set point, an LED on the module is illuminated and the output is sent low.

32.00 Price Excluding GST of 18%

Sound detection sensor module for arduino detects whether sound has exceeded a threshold value. Sound is detected via  the microphone and fed into an LM393 op amp. The sound level set point is adjusted via an on board potentiometer. When the sound level exceeds the set point, an LED on the module is illuminated and the output is sent low.

32.00 Price Excluding GST of 18%

The CJMCU-34725 TCS34725 Color Sensor RGB Module provides digital return values for red, green, blue (RGB) and bright light sensing digital Mingguang induction return value. Color-sensitive photodiode integrated cut and localized infrared shading filter, to minimize the incident infrared spectrum components.

Analog TDS Sensor/Meter for Arduino is an Arduino-compatible TDS Meter Kit for measuring the TDS value of the water, to reflect the cleanliness of the water. TDS meter can be applied to domestic water, hydroponic, and other fields of water quality testing with this product, you can easily DIY a TDS detector to reflect the cleanliness of water to protect your health.

400.00 Price Excluding GST of 18%

The Mini LCD Digital Thermometer with Probe is designed with a black plastic shell, LCD screen display, measuring temperature by two temperature sensors, 38.2″ length cable with an integrated probe. It can show centigrade and Fahrenheit. Come with a suction cup for easy fixing on some places which you want to put on the suction base, LCD display, clock function, and button cell powered (not included here). Widely used in air-conditioning, iceboxes, icehouse, cars, houses, etc

78.00 Price Excluding GST of 18%

This is a temperature measurement module that can be used to measure environmental temperature and display it on the LCD screen. It is commonly used to measure the atmosphere and liquid temperature. Some applications include aquarium and fish tank temperature monitoring, baking cake temperature monitoring, room temperature monitoring etc.

This Golden Switch Sensor Module For Arduino simple yet effective tilt switch sensor module houses a metal ball which sits in a tube with electric contacts, as your robot or autonomous vehicle tilts, the ball rolls onto the contacts, a circuit is completed and a signal is sent back to your compatible Arduino control system.

40.00 Price Excluding GST of 18%

This capacitive touch sensor module uses the TTP224 integrated circuit, making it easy to add capacitive touch input to your project. It features 4 sensitive touch pads that make an ideal replacement for the old fashioned switches.

55.00 Price Excluding GST of 18%

The TTP223B Capacitive Touch Sensor Module is a compact and reliable digital touch switch designed for easy human-touch input. Instead of using traditional mechanical push buttons, this module detects touch using capacitive sensing technology, making it more durable and stylish for modern electronic projects.

20.00 Price Excluding GST of 18%

The TTP223 Touch Key Module is based on a touch-sensing IC (TTP223) capacitive touch switch module. A capacitive touch sensor module based on the dedicated TTP223 touch sensor IC. The module provides a single integrated touch sensing area of 11 x 10.5mm with a sensor range of ~5mm.

12.00 Price Excluding GST of 18%

The TTP226 is an integrated touchpad detector IC featuring 8 touch keys. This detection IC is specifically engineered to replace traditional direct button keys with pads of various sizes. Utilizing capacitive touch technology, it enables electronics to detect when a finger is in close proximity to a surface, effectively simulating a button press similar to traditional pushbuttons. Capacitive sensing can be employed in applications where low to no force human touch sensing is preferred, offering versatile functionality across various devices and interfaces.

120.00 Price Excluding GST of 18%

The Turbidity Sensor emits at its end an infrared light, imperceptible to human vision, capable of detecting particles that are suspended in water, measuring the light transmittance and the dispersion rate, which changes according to the Amount of TSS (Total Suspended Solids), increasing the turbidity of the liquid whenever levels increase.

520.00 Price Excluding GST of 18%

Specifically designed for the HC-SR04 Ultrasonic Sensor Module, with this Ultrasonic Sensor Mounting Bracket you can attach the Hc-SR04 module to your application such as small robots or DIY projects very quickly and conveniently.

22.00 Price Excluding GST of 18%

The Ultrasonic Sensor uses Ultrasonic waves to determine the distance of an object like Bats, hence it can be used as a distance measuring sensor. There are two Ultrasonic Transducers present in which one acts as a Transmitter which transmits a high frequency Ultrasonic signal and other acts as a receiver which will wait for the receiving of echo signal which gets reflected by any object in its path. The time between the two signals when divider by speed of sound gives us the distance of the object.

55.00 Price Excluding GST of 18%

The UV Sensor is used for detecting the intensity of incident ultraviolet(UV) radiation. This form of electromagnetic radiation has shorter wavelengths than visible radiation. It is based on sensor GUVA-S12SD. It has a wide spectral range of 200nm-400nm. The module will output an electrical signal which is varied with the change of the UV intensity. UV sensors are used for determining exposure to ultraviolet radiation in the laboratory or environmental settings.

375.00 Price Excluding GST of 18%

Vibration sensor module alarm Motion sensor module vibration switch SW-420 module based on the vibration sensor SW-420 and Comparator LM393 to detect if there is any vibration that beyond the threshold. The threshold can adjust using an onboard potentiometer. When this no vibration, this module output logic LOW the signal indicates LED light, and vice versa. If the module does not vibrate, the vibration switch was closed on state, the output of low output, and the green indicator light. The product vibrates, vibration switches momentary disconnect, the output is driven high, and the green light does not shine.

38.00 Price Excluding GST of 18%

The SW520D Tilt Sensor Module is a simple motion-detection module that senses orientation and tilt using the SW520D tilt switch. It outputs a digital signal whenever the module’s position changes, making it ideal for angle detection, vibration sensing, and motion-triggered applications. Compact and easy to interface, it works seamlessly with Arduino, ESP32, Raspberry Pi, and other microcontrollers for use in DIY electronics, robotics, alarms, and smart devices.

40.00 Price Excluding GST of 18%

It can detect an object within its range even the object’s surface is highly reflective hence measuring distance accurately. It has an integrated Single Photon Avalanche Diodes (SPAD) array. This array is fast and is able to distinguish between different photons with less lag/jitter i.e within a few tens of picoseconds. The time-of-flight technology used in this sensor is ST’s second-gen FlightSense technology. The laser used here is a 940 nm Vertical-Cavity Surface-Emitting Laser (VCSEL) which is invisible and safe for the human eyes. The integrated IR filters enhance the long-range and increase immunity to the ambiance and give good prevention from glass optical crosstalk.

125.00 Price Excluding GST of 18%

AC Voltage Sensor Module ZMPT101B (Single Phase) is the best for the purpose of the DIY project, where we need to measure the accurate AC voltage with a voltage transformer.

90.00 Price Excluding GST of 18%

The Arduino analog input is limited to a 5 VDC input. If you wish to measure higher voltages,this module allows you to measure voltages of 0-25V. Keep in mind, you are restricted to voltages that are less than 25 volts. More than that and you will exceed the voltage limit of your Arduino input. Perfect for use in various electronics projects in India, Voltage Sensor Module 25V ensures reliability and performance. Ideal for various electronics projects, Voltage Sensor Module 25V offers quality and performance.

18.00 Price Excluding GST of 18%

XH-W1219 12V Digital Red+Green Display Temperature Controller Module W/ NTC Waterproof Temperature Sensor. The XH-W1219 thermostat module with its µC and I/O (sensor input, keys, double display, relay) can be re-programmed for automation tasks, and it’s easy to work with. Digital thermostat module. The temperature controller/switch with waterproof NTC probe and integrated LED display in red and green.

168.00 Price Excluding GST of 18%

This water flow sensor is connected in line with the liquid whose flow rate has to be measured. There is a simple rotating wheel with a magnet and when the liquid flows the wheel is rotated and a Hall effect sensor measures how many times the wheel is rotated and accordingly gives pulses. By counting the number of pulses you can easily calculate the flow rate as well as the amount of liquid dispensed.

800.00 Price Excluding GST of 18%

Measure water (liquid) flow in your application using this 1/2″ Brass water flow sensor. This is good quality flow sensor with brass body and can be used for industrial and commercial applications. This half inch water flow sensor is used extensively is various types of vending machines.

1/4 ” Brass Water Flow Sensor-SEN-HZ41WC, The pulse signal water flow sensor is widely applied in industrial equipment, agricultural equipment, and household electrical appliances in the future.

190.00 Price Excluding GST of 18%

The YF-S401 Water flow sensor is a small device comprising a plastic valve body, a water rotor, and a hall effect sensor. As water flows through the Water flow sensor, the internal rotator changes its speed in accordance with the rate of flow, and the hall effect sensor outputs a series of digital pulses. This allows the flow rate to be accurately measured using a microcontroller.

190.00 Price Excluding GST of 18%

The YF-S201 water flow sensor is a device that is used to measure the flow rate of water. It consists of a turbine-type rotor that is placed in the water stream, and as the water flows past the rotor, it causes the rotor to spin. The sensor measures the speed of the rotor and converts it to a flow rate. The sensor has a digital output, which means that it provides a digital signal that can be read by a microcontroller or other host device.

184.00 Price Excluding GST of 18%

Water sensor brick is designed for water detection, which can be widely used in sensing the rainfall, water level, even the liquate leakage. The brick is mainly comprised of three parts: An Electronic brick connector, a 1 MΩ resistor, and several lines of bare conducting wires.

18.00 Price Excluding GST of 18%

The Si7021 temperature and humidity sensor offer an accurate, low-power, factory-calibrated digital solution ideal for measuring humidity, dew-point, and temperature, in applications ranging from HVAC/R and asset tracking to industrial and consumer platforms. e. It can be used as hardware and software-compatible drop-in upgrades for existing RH/ temperature sensors.